This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
bitcomet_client_issues_and_possible_solutions [2011/06/14 07:56] greywizard [Tasks have disappeared/deleted tasks reappeared in my tasklist after a BitComet restart. How can I fix this?] |
bitcomet_client_issues_and_possible_solutions [2012/08/09 15:17] greywizard [When BitComet is running my router/modem reboots itself or freezes. Why is this happening and what can I do to fix this?] - Added point nr.4 in list |
||
---|---|---|---|
Line 232: | Line 232: | ||
- Next, set the // | - Next, set the // | ||
- (Optional) If you're using Windows XP, you may also want to set the number of maximum embryonic connections allowed by Windows to something a little higher than the default 10 (by using the [[bitcomet_options# | - (Optional) If you're using Windows XP, you may also want to set the number of maximum embryonic connections allowed by Windows to something a little higher than the default 10 (by using the [[bitcomet_options# | ||
+ | - Another thing you might want to watch out for is the number of simultaneous running tasks BitComet has since incoming TCP connections and UDP traffic for each additional task cannot be stopped before the router so each different IP source will create a new entry in the NAT table. Starting out with 1-2 running tasks in total (both downloading and seeding) might be a good place to begin, along with all the above measures if you encounter this type of issue. | ||
- If after doing all the above your problem still isn't solved, then it means that the culprit here is probably the UDP transport protocol. BitComet may communicate with very large number of different IPs using UDP, on account of DHT messages which use UDP as a transport protocol as well as Torrent Exchange. Each UDP datagram outgoing towards a different IP address will create a new entry in the NAT table of your router, so it can easily become cluttered simply on account of UDP traffic.\\ | - If after doing all the above your problem still isn't solved, then it means that the culprit here is probably the UDP transport protocol. BitComet may communicate with very large number of different IPs using UDP, on account of DHT messages which use UDP as a transport protocol as well as Torrent Exchange. Each UDP datagram outgoing towards a different IP address will create a new entry in the NAT table of your router, so it can easily become cluttered simply on account of UDP traffic.\\ | ||
An option in BitComet, that you can use to contain this effect, is // | An option in BitComet, that you can use to contain this effect, is // | ||
- | Summed with the 200 you set for TCP, this will give a max number of 500 entries BitComet can place any minute in the NAT table. | + | Summed with the 200 you set for TCP, this will give a max number of 500 entries BitComet can place any minute in the NAT table, on behalf of outgoing traffic. |
If the above settings work for you, then you should start to gradually increase the values until you find some values which make the issue re-appear and then stay below that threshold. For instance, you may try to first increase the number of TCP connections, | If the above settings work for you, then you should start to gradually increase the values until you find some values which make the issue re-appear and then stay below that threshold. For instance, you may try to first increase the number of TCP connections, | ||
Line 366: | Line 367: | ||
If it's not then recheck the %appdata% permissions -- often you need to check all the permissions for the entire tree and every node in it. The account you usually run BitComet under - normally your own - should own the directory and files, and have full control of both. | If it's not then recheck the %appdata% permissions -- often you need to check all the permissions for the entire tree and every node in it. The account you usually run BitComet under - normally your own - should own the directory and files, and have full control of both. | ||
+ | |||
+ | ==== How can I transfer all my tasks to another computer? ==== | ||
+ | |||
+ | If you wish to move all your tasks (active and/or stopped) to a new computer and hence to a new installation of BitComet you will have to follow a few easy steps: | ||
+ | - Copy the current BitComet download folder (the folder which holds the files for each task) onto the new computer and make sure that it resides in a partition which has the same letter as the previous one (i.e. if your current download folder is // | ||
+ | - Go to the //File// menu and choose //Import and Export Download List...//. In the lower section named " | ||
+ | - Select all the tasks in the Task List of BitComet and then right click and choose //Save Torrent As// and save all the .torrent files into a location of your choice. | ||
+ | - Make sure that in your new installation of BitComet the variable // | ||
+ | - Open a new Explorer window and type in the address bar // | ||
+ | - Go into the // | ||
---- | ---- | ||
-[[understanding_bitcomet|Previous Page]] -[[configuration_and_user_settings|Next Page]]\\ | -[[understanding_bitcomet|Previous Page]] -[[configuration_and_user_settings|Next Page]]\\ | ||
-[[start|Main Index]] | -[[start|Main Index]] |